NEIEP 200 FINAL EXAM V1 NEW
2023/2024 EDITION
you are preparing the assemble the car sling on a hydro. what are the components
... [Show More] -
ANSWERS-crosshead, stiles, bolster channel
you are preparing to hoist rails and are inspecting your manila rope. which of the
following is a good characteristic of manila rope? - ANSWERS-a light yellow color with a
silvery or pearly luster
you are preparing to install comp chains and notice there are two sets of hitch points.
which ones should you initially use? - ANSWERS-two nearest the counterweight
you are preparing to install machine beams for a geared traction machine and have
established the centerline of the car and counter weight rails. what does this centerline
represent - ANSWERS-drive sheave centerline
you are preparing to install the compensating ropes. where should the reels and jacks
be set up - ANSWERS-lowest access point
you are preparing to lift a load and need to tie the ends of two ropes together. which
knot should you use? - ANSWERS-square
you are preparing to unload a truck at the loading dock and the truck is 8" higher than
the dock. what do you do? - ANSWERS-use a steel plate to span the gap
you are preparing to use a chainfall to lift a load up a hoistway. what safety equipment is
required on each of the two hooks on the chain fall? - ANSWERS-tags
you are ready to cut the dead end excess after reshackling. how far past the socket
should you cut it - ANSWERS-6-9"
you are reroping and elevator and have selected two chainfalls to hang the car. the total
weight of the car is 4000. what should be the minimum capacity of each chain fall -
ANSWERS-4000 lbs
you are rigging elevator equipment with a sling angle of 60 degrees. you are using a
shouldered eye bolt with a tapped 1/2" diameter hole. once the shoulder is seated, what
is the minimum thread depth required? - ANSWERS-at least 3/4"
you are selecting a wire rope sling to rig 1000lbs. what safety factor does asme require?
- ANSWERS-5:1
you are setting up welding equipment. what is the maximum psi that the regulator for
the acetylene gas may be adjusted to? - ANSWERS-10-12 psi
you are storing fiber core wire rope slings. what could cause damage to the core
material? - ANSWERS-solvents
you are tasked with setting 3/4" concrete anchors. which type of drill should you use? -
ANSWERS-rotary hammer
you are tensioning the ropes on an elevator that has two different length of shackles.
how must you tension the ropes - ANSWERS-shackles must be equally tensioned
you are using a bowline knot- what is one disadvantage of this knot - ANSWERS-is can
easily loosen when not loaded
you are using a plumb line to check a rail for plumb. you find that at the top it measures
1" and at the bottom it measures 1 1/4". what does this tell you? - ANSWERS-a. the top
of the rail needs to go towards the center
b. the top of the rail needs to go toward the wall
c. the bottom of the rail needs to go toward the wall
you are using rollers to move a heavy elevator machine and are approaching a corner.
which technique should you use to maneuver around it? - ANSWERS-angle front roller
gradually and continue around the corner
you are working in a pit 72" deep. what does asme require regarding stop switches? -
ANSWERS-a second stop switch must be installed 47" above the pit floor
you are working in a pit deeper than normal. what can you do to bring the buffers up to
the proper height? - ANSWERS-buffer stands
you are working on an elevator machine and you notice the drive sheave and brake
drum are directly mounted on the motor shaft. what machine are you working on? -
ANSWERS-gearless
you arrive at a job and notice the counterweight has a governor. what does this mean -
ANSWERS-there's an occupied space below
you have constructed a wooden template for position a basement geared traction
machine to its foundation. what two machine centerline reference points must be
marked on the template to properly orient the foundation bolt holes - ANSWERS-worm
shaft, sheave shaft [Show Less]